Perma-pure Baldwin-Series 10410 Manuel d'utilisateur télécharger pdf (Page 34)

2. Multi-Channel Mounting

Flat bladed screwdriver required for mounting.

Tubing loading key required for mounting.

Note:

Other special mounting hardware for multi-channel pumping.

See “ 3. Replacement Parts and Accessories”.

a) Load the pump heads with tubing.

b) Install the four correct length-mounting screws in drive.

c) Slide the first pump head into the mounting screws.

d) Place key in slot on mounting shaft. Twist to align tang on rotor

shaft with slot in motor drive shaft. Shift the pump housing

around till it drops over the alignment pins (if present).

e) Repeat for each additional pump head, aligning pump head tang

with slot on previously mounted pump head.

f) Slide the four flat washers onto screws and secure with the four

wingnuts. Tighten with fingers only.

g) A support bracket is supplied with 3 and 4 channel mounting

hardware for additional support. Mount over bottom two screws.

Inert one of the three different adjustments screws depending

upon drive height.

3. Replacement Parts and Accessories

A. End Bells

(order two end bells for a complete head assembly).

Pump Head #

PC Order number

Pump Head #

PC Order

number

07013-00, -20

07013-10, -21

MN-07013-81

MN-07013-91

07013-50, -52

MN-07013-92

07014-00, -20

07014-10, -21

MN-07014-81

MN-07014-91

07014-50, -52

MN-07014-92

07015-00, -20

07015-10, -21

MN-07015-81

MN-07015-91

07015-50, -52

MN-07015-92

07016-00, -20

07016-10, -21

MN-07016-81

MN-07016-91

07016-50, -52

MN-07016-92

07017-00, -20

07017-10, -21

MN-07017-81

MN-07017-91

07017-50, -52

MN-07017-92

07018-00, -20

07018-10, -21

MN-07018-81

MN-07018-91

07018-50, -52

MN-07018-92

07024-00, -20

07024-10, -21

MN-07024-81

MN-07024-91

07024-50, -52

MN-07024-92

07035-02, -20

07035-12, -21

MN-07035-81

MN-07035-91

B. Rotor assemblies

Pump Head number Pump Head suffix

Order number

07013, 07014, 07016

07018

-00

-10, -50

-20

-21, -52

MN-07013-75

MN-07013-76

MN-07013-80

MN-07013-95

07015, 07024, 07035

-00, -02

-10, -50, -12

-20

-21, -52

MN-07013-75

MN-07013-76

MN-07013-80

MN-07013-90

C. MN-07021-04 Thrust washers.

Pack of 10.

D. MN-07013-90 Tubing loading key.

E. Mounting hardware for standard pump heads

Set contains four #8-32 screws, four washers, and four wingnuts.

Number of heads

To be mounted

Cold- rolled steel

Order number

Stainless steel

Order number

MN-07013-02

MN-07013-03

MN-07013-07

MN-07013-04

MN-07013-05

MN-07013-08

MN-07013-09

4. Specifications

Thin wall* Thick wall*

Maximum continuous

discharge pressure-psi(bar): 20(1.4) 25(1.7)

Maximum intermittent

discharge pressure-psi(bar): 35(2.4) 40(2.7)

Maximum vacuum: 660(510’)m Hg 26(20’)in Hg

Maximum suction lift: 8.8(6.7’)m H2O 29(22’)ft H2O

Number of rollers: 3

Occlusion: Standard fixed

Maximum pump speed (rpm): 600

Nominal torque load: 6.5 kg-cm(90 oz-in)

Housing materials: Polycarbonate (PC) all models, or Polyphenylene

sulfide (PPS) all models except 07035

Roller/rotor materials: Cold rolled Stl (CRS) or Stainless Stl (SS)

Operating temperature: 0 to 40° (32 to 104°F)

*Thin wall: tubing 13, 14, 16, 17, 18 Thick wall: tubing 15, 24, 35

ɈWith tubing 17 & 18

ū Use in this temperature range for continuous duty operation with no

decrease in performance or product life. Pump heads will work outside

this range with some possible reductions in performance or product

life.

5. Warranty and Return Items

Warranty

Use only MASTERFLEX Precision Tubing with MASTERFLEX Pumps

to insure optimum performance. Use of other tubing may void

applicable warranties.

The manufacturer warrants this product to be free from any significant

deviations from published specifications. If repair or adjustment is

necessary within the warranty period, the problem will be corrected at

no charge if it is not due to misuse or abuse on your part, as determined

by the manufacturer. Repair costs outside the warranty period, or those

resulting from product misuse or abuse, may be invoiced to you.

The warranty period for this product is noted on the Warranty Card.

Product Return

To limit charges and delays, contact the seller or manufacturer for

authorization and shipping instructions before returning the product,

either within or outside the warranty period. When returning the

product, please state the reason for the return. For your protection, pack

the product carefully and insure it against possible damage or loss. Any

damages resulting from improper packaging are your responsibility.

Technical Assistance

If you have any questions about the use of this product, contact the

manufacturer or authorized dealer.

1 2 ... 29 30 31 32 33 34 35 36

Commentaires sur ces manuels

Pas de commentaire

Perma-pure Baldwin-Series 10410 Manuel d'utilisateur Page 34

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Perma-pure Baldwin-Series 10410